Katie Grzesiak Posted April 20, 2016 Report Share Posted April 20, 2016 Here's a quick overview of the treatments ISN has found most successful for controlling knotweeds: Milestone (aminopyralid) Faster kill (~3 years), more off-target effects Standard rate (3-7 oz/acre; 0.01%) Using nonionic surfactant (standard rate) Late spring (3-4 ft high) or late summer (at least 60 days before frost) When treating in late summer, it is helpful to do a cut of the plants a month or so in advance ONLY IF safe disposal of the stems is possible At some sites, repeat treatments (spring & summer) may be appropriate, so long as maximum application rates are not reached Not aquatic approved Note: Tree sensitivity issues--some trees will die if their roots mingle with knotweed that is treated with Milestone. Clearcast (imazamox) Acceptable kill (~5 years), fewer off-target effects Cocktail: 5% Clearcast 1-2% Methylated Seed Oil (MSO) Not all MSOs are aquatic-approved!! Check before applying to knotweed in areas with standing water 1-2% glyphosate (aquatic-approved formulation) Best sprayed in late summer/early fall Spraying at least 60 days before the first frost is CRUCIAL--this date will vary by location (for northwest lower MI, it's early August) Aquatic approved (if adjuvants are aquatic-approved) We have applied both of these treatments as either foliar spray or as a "cut stem" application (cutting down stems and filling the stem cavity with herbicide solution), which is a great way to avoid drift and overspray, but is more time-intensive and contains the risk of stem disposal. Questions? Comments? Leave a note! Quote Link to comment Share on other sites More sharing options...
Katie Grzesiak Posted April 20, 2016 Author Report Share Posted April 20, 2016 Also, please note that this is NOT a substitute for reading pesticide labels! Make sure you're in compliance with laws and policies (and have landowner permission) before doing any control practices. Quote Link to comment Share on other sites More sharing options...
Stephanie Hoyle Posted April 28, 2016 Report Share Posted April 28, 2016 Do you know what the die off percentage is from the year one treatment is for each species? Also, after the plant has been sprayed when get the material that appears dead be cut, mowed, removed? Thanks, K Quote Link to comment Share on other sites More sharing options...
Katie Grzesiak Posted May 3, 2016 Author Report Share Posted May 3, 2016 Unfortunately, the die-off percentage varies greatly by site (likely due to age etc.). I would hazard an estimate of approximately 50% die-off in the first year with Milestone, and perhaps 30% for Clearcast. Since it's a multi-year project no matter what, we've been looking more at the long-term effects, where Milestone comes out ahead. Truly dead plant material can be removed from the site as soon as it is bone-dry and therefore incapable of regenerating elsewhere. We advise our landowners to wait until late fall or even winter/spring to take the guesswork out of it, but if they want to monitor the stems to see when they're properly desiccated. Quote Link to comment Share on other sites More sharing options...
Stephanie Hoyle Posted May 23, 2016 Report Share Posted May 23, 2016 Hi Katie, Thanks for all of the great information. Can you give me an idea on the dates you mean for "late spring"? Thanks, K Quote Link to comment Share on other sites More sharing options...
Katie Grzesiak Posted May 23, 2016 Author Report Share Posted May 23, 2016 "Late spring" and "late summer" have much more to do with phenology than actual dates. We consider late spring to be when the knotweed is 3-4 ft high, and late summer as at least 60 days before frost. Here in northwest lower Michigan, that translates to mid-June and mid-August. Saginaw Bay area may be different. Quote Link to comment Share on other sites More sharing options...
Leslie Clark Posted June 4, 2018 Report Share Posted June 4, 2018 Any update on this? I'm curious about using the Clearcast cocktail as a cut-stem application. Are you using the same concentration as for spraying? Quote Link to comment Share on other sites More sharing options...
Katie Grzesiak Posted June 4, 2018 Author Report Share Posted June 4, 2018 Unfortunately, not really any updates. We've moved away from doing cut-stem and into doing injections due to the complications of disposal, but we've only been doing injections for about a year, and don't have much to report yet. Quote Link to comment Share on other sites More sharing options...
Fields Ratliff Posted July 20, 2018 Report Share Posted July 20, 2018 I only have one experience using Clearcast + Aquaneat for cut-stem. As Katie mentioned, we don't typically do this due to disposal issues. In this case, we worked with the landowner to properly cut, dry, and burn the the knotweed on their property. Anyway, the treatment occurred in September and had really good results. I've attached a before and after picture. One is from September 2016 (before) and the other is from June 2017 (after). Hope that helps! Quote Link to comment Share on other sites More sharing options...
Leslie Clark Posted July 21, 2018 Report Share Posted July 21, 2018 (edited) That's encouraging. I'm looking for clarity on the concentration used with Clearcast for cut stem. When I've used aquaneat alone for cut stem, I've used 25%-50%, vs the usual 2%-4% for spraying and it is relatively cheap to use even at high concentrations. Clearcast is usually 5% volume-to-volume for spraying, so 6.4oz/gallon. At $300/gallon, spraying it is expensive enough. I can't imagine using it straight for cut stem given the price. So I'm looking for confirmation that the cocktail used for cut stem is the same as that used for spraying: that is, 5% Clearcast v-to-v, 1.5% aquaneat, and some MSO. Is that what you used for your cut stem application? Edited July 22, 2018 by Leslie Clark remove quoted response Quote Link to comment Share on other sites More sharing options...
Abigale Bristol Posted May 12, 2021 Report Share Posted May 12, 2021 Hey folx! We're gearing up for some Japanese knotweed management, and I'm trying to determine our best go-to options. BMPs often suggest cutting JK before a foliar spray because the plant can get too tall, but it sounds like that practice gets dropped pretty quick because of the disposal issue. For patches that have too many stems for the injection method, and with plants that are too tall for foliar spraying, are y'all still opting to cut the stems and return to foliar spray? Let me know your thoughts! Thanks, Abbie Quote Link to comment Share on other sites More sharing options...
Katie Grzesiak Posted May 17, 2021 Author Report Share Posted May 17, 2021 We'd really like to do the cut-and-return, but can't spare the staff time. We time so we treat when the plant is smaller the first year (it's usually shorter after the first year of spraying) and bring a ladder just in case. That said, if you CAN do the cut, or if the landowner can do it responsibly and leave the cut stems in place (we have a few that do!), research shows that it can be a lot more effective. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.